PDFFeaturesnSpecific weight: 1.750 kg/lnDilution: ready to usenAvailable in the following granulometry: 0.6, 1.2, 1.5, 2.0n nnConsumptionnGranulometry 0.6 mm: 2.5 kg/m2 with two handsnGranulometry 1.0 mm: 2.0 kg/m2nGranulometry 1.2 mm: 2.3 kg/m2nGranulometry 1.5 mm: 1.5 kg/m2nGranulometry 2.0 mm: 3.0 kg/m2 with two handsnIt allows to obtain a finishing surface with a rustic effect.nn nnTechnical DatanCertificato CEnnEN 15824nn nnSPEED TRANSMISSION OF STEAM EN ISO 7783-2nCategory Spread equivalent to the thickness of the air layer Sd/mnV2 Medium Value between ?0,14 <1,4nWATER ABSORPTION EN 1062-3nCategory Spread equivalent to the thickness of the air layer Sd/mnW3 Low ?>Value between ?0,14 <1,4>nGRIP EN 1542 (test carried out in a time of 28 days mandatory technical)nAll measured values must be at least 0.3 MPa (mean value recorded 1.58 Mpa)nDURABILITY EN 13687-3nAll measured values must be at least 0.3 MPa (mean value recorded 2.34 Mpa)nn.b. prove effettuate da:nN.B. Tests done by: Laboratory aut. by the Ministry of Infrastructure and Transport P.C.S. LL.PP.S.T.C. -law November 5 1971 n. 1086 Dec. N ? 56300 of 14/03/2007 Laboratory aut. by the Ministry of Infrastructure and Transport P.C.S. LL.PP.S.T.C. ? Presidential Decree No. 380/01 art. 59 circ. n ? 349/99 weeks. a), b) and c) Dec. n ? 53362 of 06/05/2005 Notified Body n ? 1308 (DM 826 149 of 22/03/2004 of the Ministry of Industry) under Dir. 89/106 / EEC, DPRnNo. 246/1993, DM 156/2003
Siloxan INTO
Siloxan INTO
SILOXAN INTO is a finishing coating formed of special water-based acryl-siloxanic binders that bestow at the same time water-repellence, breathability and resistance to external agents.
Lectus hac tortor congue habitasse consectetur. Nibh id sapien libero mollis vehicula nostra accumsan potenti cras imperdiet.
UsenSILOXAN INTO is used as protective and decorative coating for indoor and outdoor use, on bottom plasters with a lime-cement base, especially where having at the same time high transpirability and low water absorption is necessary.nn nnBase preparationnThe finishing coating must be applied after at least 28 days from the bottom plaster application.nThe surface needs to be dry and clean, without any other greasy spots and must be completely clean.nn nnApplicationnLay the material on the surface with a metallic spatula taking care of distributing one uniform layer of material. The finishing must be completed with a plastic spatula making circular movements. To apply the product with a fine 0.6 mm granulometry, you need 2 layers of material.nThe second layer must be applied when the first one is completely dry.nn nnWarningsnFor every work just take the needed material all of the same kind.nApply the material only over seasoned and dried plasters.nAvoid the application on facades with full sun and too much wind.nAvoid the application during the coldest and most humid months of the year; a temperature of +5 ?C is the lowest value for the laying-up and drying of the material.nAfter applying, the surfaces must be protected by rain for at least 48 hours.nAvoid the application of the material over a facade in different times.nSILOXAN INTO must be used at its original status without adding other materials.nn nnSupplyn25 kg can.nTints: see the colors folder.n nnPreservationnPreserve the product in right places. If stocked inside the original can it lasts 1year.nn nnQualitynSILOXAN INTO is constantly and properly checked in our laboratories. The raw materials used are strictly selected and checked.UsenSILOXAN INTO is used as protective and decorative coating for indoor and outdoor use, on bottom plasters with a lime-cement base, especially where having at the same time high transpirability and low water absorption is necessary.nn nnBase preparationnThe finishing coating must be applied after at least 28 days from the bottom plaster application.nThe surface needs to be dry and clean, without any other greasy spots and must be completely clean.nn nnApplicationnLay the material on the surface with a metallic spatula taking care of distributing one uniform layer of material. The finishing must be completed with a plastic spatula making circular movements. To apply the product with a fine 0.6 mm granulometry, you need 2 layers of material.nThe second layer must be applied when the first one is completely dry.nn nnWarningsnFor every work just take the needed material all of the same kind.nApply the material only over seasoned and dried plasters.nAvoid the application on facades with full sun and too much wind.nAvoid the application during the coldest and most humid months of the year; a temperature of +5 ?C is the lowest value for the laying-up and drying of the material.nAfter applying, the surfaces must be protected by rain for at least 48 hours.nAvoid the application of the material over a facade in different times.nSILOXAN INTO must be used at its original status without adding other materials.nn nnSupplyn25 kg can.nTints: see the colors folder.n nnPreservationnPreserve the product in right places. If stocked inside the original can it lasts 1year.nn nnQualitynSILOXAN INTO is constantly and properly checked in our laboratories. The raw materials used are strictly selected and checked.
